Miele Appliance Error Codes

Dishwasher Error Codes

• F11 This error code indicates a problem with water drainage.
• F12/F13 These fault codes signify a water intake error.
• F14 The F14 error code indicates a problem with the heater pressure switch.
• F24 Heating Error: Water not heating.
• F25 Turbidity Sensor Error: Soil sensor malfunction.
• F32 When the door lock fails to close properly, the F32 error code appears.
• F40, F47 This error code related to the control board
• F70 The F70 code indicates a problem with the float switch, which detects the water level inside the dishwasher.
• F78/F79 This error code relates to a fault in the circulation pump

Warming Drawer Error Codes

• F1 Temperature Sensor Error: Drawer cannot monitor temperature.
• F4 Heating Element Error: Drawer not heating properly.
• F7 Communication Error: Control board communication failure.
• F10 Overheating: Drawer overheated.
• F19 Power Error: Voltage or power board issue.
• F32 Mechanism Error: Drawer runners or motor jammed.

Refrigerator, Freezer and Wine Cooler Error Codes

• NA Serves as a warning temperature increased during a power failure that lasted for an extended period
• FE Code might signal temperature fluctuations, Sensor Troubles, Defrosting Problems.
• F0 Temperature Sensor Fault: Incorrect data affects cooling
• F1 Temperature Sensor Fault: The internal temperature sensor is giving incorrect readings, causing unstable cooling performance.
• F2 Evaporator Sensor Failure: Ice buildup and cooling issues may occur.
• F3 A malfunctioning air sensor in the freezer.
• F4 Evaporator Sensor Fault: The evaporator sensor is malfunctioning, potentially leading to frost buildup and reduced efficiency.
• F5 Control Electronics Fault: The main control board is experiencing a malfunction that disrupts cooling cycles.
• F10 Defrost Heater Error: Defrost cycle cannot operate.
• F41 Power Module Error: Electrical instability detected.
• F110 Air Sensor Fault: Incorrect air temperature readings affect overall temperature regulation.
• F115 Evaporator Zone Sensor Fault: One of the cooling zones cannot maintain proper temperature due to inaccurate sensor data.
• F120 Voltage Fault: Unstable voltage has been detected and the unit may shut down for protection.
• 01, _F, 21 An indication that something is amiss with the ice production system.

Microwave and Speed Oven Error Codes

• F01 / F02 Temperature Sensor Fault: The internal temperature sensor (NTC) is open or short-circuited.
• F11 Drain Fault: (For Combi-Steam models) Water cannot be pumped out; the drain hose or pump may be blocked.
• F32 Door Logic Failure: The door limit switches are not synchronized, or the door latch mechanism is defective.
• F38 Power Module Defect: The high-voltage inverter electronics have failed; microwave heating is disabled.
• F44 Communication Error: The main control unit cannot communicate with the display or keyboard interface.
• F47 Interface Failure: A transmission error occurred between the user interface and the power electronics.
• F55 Safety Cut-Out: The appliance has exceeded the maximum operating time for safety reasons.
• F83 Cooling Fan Error: The fan responsible for cooling the magnetron is not rotating at the correct speed.
• F103 Bottom Heater Fault: (Speed Ovens) The lower heating element is open or malfunctioning.
• F267 Keypad Stuck: A button on the touch control panel is detected as stuck in the pressed position.
• Door Door Contact Switch: The system does not recognize the door as closed; interlock switches may be misaligned.
• System Lock Child Safety Lock: The appliance is electronically locked to prevent accidental operation.

Washing Machine Error Codes

• F10 Water Intake Fault: The machine is not filling with water properly or the flow is too slow.
• F11 Drainage Fault: Water is unable to drain from the drum; the filter or hose may be blocked.
• F16 Overdosage: Too much detergent or excess foam has been detected during the cycle.
• F20 Heating Fault: The water is not reaching the required temperature within the set time.
• F34 Door Lock Mechanism: The door failed to lock properly and the cycle cannot start.
• F35 Door Release Failure: The door lock is jammed and cannot open automatically.
• F50 Drive System Failure: The motor is not running or the drum is failing to rotate.
• F53 Speed Sensor Error: The system cannot detect the speed of the drum (tachometer issue).
• F63 Water Path Control: An error occurred in the water distribution or sensor unit.
• F138 Waterproof System Activated: A leak has been detected in the base of the machine; water supply is cut off.
• F220 Water Supply Issue: The water pressure is too low or the inlet filter is clogged.
• System Lock Child Safety Lock: The machine is locked to prevent accidental operation.

Range, Stove, Oven, Cooktop & Microwave Error Codes

• F10 Temperature Sensor Fault: The oven or cooktop sensor is malfunctioning, resulting in incorrect temperature regulation.
• F11 Temperature Sensor Fault: Faulty sensor data reduces heating precision.
• F14 Heating Element Failure: The primary heating element is damaged or not responding to commands.
• F20 Overheating Detected: Excessive temperatures triggered the safety shutdown system.
• F23/F32/F33 Induction Coil Error: Cookware detection malfunction.
• F24 Heating Circuit Overload: Excess electrical load detected in the heating circuit.
• F27 Board Communication Error: Internal boards cannot sync properly.
• F34 Power Supply Issue: Unstable voltage detected.
• FE36 Touch Panel Error: Unresponsive or glitching touch controls.
• FE37, FE44 or F44 This is the overheating protection. The cooktop turns off automatically as a precaution.
• F40 Communication Error: Internal modules not communicating.
• F41 Power Control Fault: Voltage or power board issues are preventing normal operation.
• F44 there's a technical error. Turn the oven off for half a minute by pulling the connector from the socket or by switching the fuse in the fuse box.
• F55 means that the oven turns itself off automatically. This happens due to safety reasons when you use the oven for a very long time.
• F47/F48/F49, FE47 or FE48 This means an error or blockage of the fan.
• F54 occurs with oven with a meat thermometer and it indicates that it's broken.
• F60 If you see this code, there's a problems with the ventilation.
• F63 Touch Panel Malfunction: The touch control surface is unresponsive or behaving erratically.
• F80 Cooling Fan Error: The cooling fan cannot maintain required speed.
• FE91, FE92, FE93, FE94, or F30 When this error appears on the display, the cooktop isn't getting enough or getting too much voltage.
• LC or LOC The child safety lock has been turned on.
• dE This isn't an error, but indicates that the cooktop has been set to demonstration mode.

Ventilation Hood Error Codes

• F1 Grease Filter Sensor Fault: The system cannot detect filter condition correctly.
• F2 Fan Motor Failure: The fan can't start or maintain speed.
• F4 Temperature Sensor Error: Temperature readings are inaccurate.
• F7 Control Panel Error: Buttons/touch controls not responding correctly.
• F10 Lighting Failure: Light circuit malfunction.
• F19 Voltage Irregularity: Power fluctuation detected.

Dryer Error Codes

• F1 / F2 NTC heater sensor has short-circuited
• F10 Water intake fault. Possible inlet valve issue
• F11 Draining issues
• F15 Hot water intake issue
• F16 Excessive amount of detergent detected
• F19 Flow meter slow
• F20 Heater fault
• F29 Heater steam inactive
• F32 This error code appears when the door is unable to lock properly. It could be due to a faulty hinge or a malfunctioning door lock mechanism. To have this fixed, call a professional to replace the necessary parts.
• F39 Electronic unit fault
• F41 Faulty EEPROM
• F45 Incorrect data
• F46 LCD connection defective
• F47 BAE / SLT interface fault
• F50 this is a general computer error that typically appears when you open the dryer door. Once again, it’s advisable to call in the pros.
• F51 Pressure sensor fault
• F53 Speed sensor fault
• F55 this is a signal that indicates an overrun time error. Use a professional to assist with this
• F62 Defective program selector.
• F63 Water path control unit error.
• F64 Path sensor fault.
• F066 Moisture Sensor Fault: Dryer cannot detect moisture properly.
• F138 Heating Error: Heating relay or element malfunction.
• F148 Communication Error: Internal electronics not communicating.
• F160 Drum Motor Failure: Drum motor is not rotating.
• F212 Temperature Sensor Error: Incorrect air temperature readings.
• F534 Airflow Restriction: Lint blockage preventing airflow.

Coffee Machines Error Codes

• F1/F2 Indicates a short-circuit in the NTC sensor, typically caused by water or heating-related problems.
• F10 Indicates a water intake issue.
• F11 Points to difficulties in water drainage.
• F15 Indicates a fault in hot water intake.
• F16 Signals the detection of excess detergent.
• F19 Indicates a slow flow meter, leading to rotation complications.
• F20 Points to heating malfunctions.
• F29 Indicates that the heater steam is inactive.
• F34/F35 Indicate problems with locking or unlocking the door.
• F39 Points to a failure in the electronic unit.
• F41 Indicates incorrect data from faulty electrical memory.
• F43 Indicates that the appliance model is not programmed.
• F45 Suggests defective Flash Ram, resulting in incorrect data supply.
• F50 Indicates a drive issue.
• F51 Points to a level switch or sensor pressure problem.
• F53 Miele washing machine fault code F53 indicates a speed sensor fault has been detected
• F56 Indicates that the final spin speed is less than 400rpm.
• F62 Points to a defective program selector.
• F63 Indicates a failure in the water path control unit.
• F65 Suggests that the drum lighting cap is missing.
• F81 Indicates that the steam is inactive in the heater unit.
• F83 Indicates excessive temperatures in the heater unit.
• F92 Indicates a risk of bacterial contamination.
• F100 Indicates a communication link failure.
• F104 Indicates low voltage to the drive.
• F138 Points to water in the drip tray.
• F140 Suggests a fault in the drainage dispenser unit.